Packet White Paper: 109\\ Paula Dowie\\ July 2001\\ ====== NET/ROM DATA MULTIPLEXING ====== ===== STATUS OF THIS MEMO ===== This document proposes a simple extension to the NET/ROM layer 4 transport protocol, allowing up to 65536 different types of "service" to be hosted on a node, using a single Secondary Station Identifier. ===== TABLE OF CONTENTS ===== 1. Introduction\\ 2. Motivation\\ 3. Discussion\\ 4. The Proposal\\ 5. Packet Format\\ 6. Receive Processing\\ ===== 1. INTRODUCTION ===== In order to provide multiple "services" on a single Net/Rom node, each service (e.g. BBS, PMS, Chat server, Dx Cluster, HTTP, Game server etc) requires a different Secondary Station Identifier (SSID). As there are only 16 possible SSID's, and therefore services, per node callsign, this limitation could stifle future development of novel services. Additionally, every service that is to be Net/Rom L4 connectable must have an entry in the NetRom "Nodes table", and those entries must be propagated via nodes broadcasts. Just 20 nodes, each with 8 services, would use a total of 160 entries. A table of that size is slow to propagate over RF links, making it difficult for the network to achieve stability. It is also cumbersome for users to view. Finally, there is no agreed standard for SSID numbers, and the "Aliases" often give no clue to what service is associated with it. This document proposes a fairly trivial solution to the above problems. If implemented, it would allow vastly more services to be carried over Net/Rom, with standardised service addresses, and zero cost to the nodes table size. ===== 2. MOTIVATION ===== The primary motivation for this proposal was a desire to allow novel services, such as HTTP, SMS, APRS, gaming and File transfer, to name but a few, to be transported over the Packet Radio network. However, it may also help alleviate other problems, as explained below. Over recent years, thanks to better connectivity, and new software which allows larger nodes table sizes, the amount of routing information being moved around the network is increasing rapidly. This is consuming valuable bandwidth, and if the trend continues, modelling suggests that the network will fail to converge to a stable, accurate state after a perturbation. By the time the last "nodes broadcast" packet has been sent, the table is already out of date. If a node user issues a N(odes) command, it may take several minutes to transmit the whole nodes table over congested RF links, and it has been observed that many users simply disconnect rather than wait for the whole table. A typical nodes table may contain multiple entries for the same node, each with a different alias and SSID, one for each service hosted by that node. There is no consistent standard for these addresses, leading to confusion, and wasted connections. As more services are added, this situation can only get worse, but this proposal offers a mitigation. ===== 3. DISCUSSION ===== Although Net/Rom may not be the BEST networking protocol, it has stood the test of time and, despite the availability of a formal protocol specification, has become the de facto standard for AX25 networking. Any attempt to replace Net/Rom would probably be doomed to failure. In order to expedite the development of novel services, a way must therefore be found to transport them over Net/Rom, without breaking anything. In contrast with NetRom, which only allows one service per address (i.e. callsign-SSID), with only 16 possible addresses per node, TCP and UDP allow up to 65536 different services per IP address. Furthermore, the important service numbers are well known and standardised. It is unlikely that Packet Radio would ever need to support as many as 65536 different services per node, but there is certainly a need for more than 16. Using TCP-like "service numbers" rather than SSID's would allow both simplification of the nodes table, and standardisation of the numbers. For example, service 0 could be a normal connection to the node's command line, service 1 might be an information server, service 2 could be the sysop's PMS, service 21 might be file transfer, and service 80 could be an HTTP server. So why not simply use TCP/IP over AX25? TCP/IP is a verbose protocol, which does not work well over low bandwidth, unpredictable RF links. In addition, it requires co-ordination, and knowledge that many sysops do not posess, nor wish to posess. It has its niche, but on radio links will never displace NetRom. NetRom needs to be more like TCP/IP, without being TCP. [large chunk missing/corrupt here!!] The service port number is only required during circuit set up. After that, the circuit numbers (along with callsigns) are sufficient to maintain the circuit. ===== 4. THE PROPOSAL ===== The proposed solution is to add an "extended" connect request to the list of NetRom L4 opcodes. This request would include the target service number. The suggested mnemonic is CREQX. Such a packet should pass unmolested through intermediate L3 routers, because the L4 header is of no concern to L3. It should in theory be ignored by legacy L4 endpoints, if they are correctly written according to the "Robustness Principle". Why Add Another Opcode? There is a "reserved" flag in the opcode/flags byte, but the NetRom designers may have earmarked that for future use, so we can't use that. Additional bytes could be appended to a normal CREQ, but that might break other people's software. So the safest option is to add another opcode. The proposed opcode for CREQX is 8, and the unused sequence number fields of a "regular" CREQ could carry the requested service number, as shown in the following comparison netween CREQ and CREQX: ===== 5. PACKET FORMAT ===== The following diagrams depict only the transport header portion of a Net/Rom frame. The layer 3 header is not affected by this proposal. Normal CREQ: ---------------------------------------------------------- | id | ndx | unused | 1 | win | usercall | nodecall | ---------------------------------------------------------- 1 1 2 1 1 7 7 Bytes Extended CREQ: ---------------------------------------------------------- | id | ndx | svch | svcl | 8 | win | usercall | nodecall | ---------------------------------------------------------- 1 1 1 1 1 1 7 7 Bytes Where id and ndx are the senders circuit ID and index as usual, svch and svcl are the high and low bytes of the target service number, 8 is the new opcode, and the remainder is as normal. ===== 6. RECEIVE PROCESSING ===== Upon receipt of CREQX, the receiving node checks whether or not the requested service is available. If it is, a CACK is sent in the usual way, and the connection is identical to "normal" NetRom. If the requested service is not available, unimplemented or busy, the connection is rejected using the CHOKE flag in the usual way.