Differences

This shows you the differences between two versions of the page.

--- packet:ninotnc [2025/03/17 19:14] – ei5iyb
+++ packet:ninotnc [2025/10/27 14:19] (current) – [Operating modes] m0gzp
@@ Line 21: / Line 21: @@
 ===== UK Stock =====
-By agreement, Tom M0LTE holds stock of PCB + microcontroller only kits in the UK. These are available with circa 2 day shipping from [[https://ko-fi.com/s/981d919ea3|https://ko-fi.com/s/981d919ea3]]. Two sets of components from Mouser takes you over their free shipping threshold.
+By agreement, Tom M0LTE sometimes holds stock of PCB + microcontroller only kits in the UK. These are available from [[https://ko-fi.com/s/981d919ea3|https://ko-fi.com/s/981d919ea3]]. Two sets of components from Mouser takes you over their free shipping threshold.
 ===== Operating modes =====
@@ Line 27: / Line 27: @@
 Current modes as of firmware release 3.40 / 4.40 / v40 (all refer to the same version)
-^# ^ Mode ^ Baud  ^ bps   ^ Mod  ^ Proto ^ Usage  ^ BW     ^ Typical use                                                                                ^
+^# ^ Mode ^QtSM Mode ^ Baud  ^ bps   ^ Mod  ^ Proto ^ Usage  ^ BW     ^ Typical use                                                                                ^
-|1 | 0001 | 19200 | 19200 | 4FSK | IL2Pc | FM     | 25k    | High SNR links between dedicated data radios. v41 firmware required in practice.           |
+|1 | 0001 | ? |19200 | 19200 | 4FSK | IL2Pc | FM     | 25k    | High SNR links between dedicated data radios. v41 firmware required in practice.           |
-|3 | 0011 | 9600  | 9600  | 4FSK | IL2Pc | FM     | 12.5k  | High SNR links between dedicated data radios. Suitable for UK 2m band.                     |
+|3 | 0011 | ? | 9600  | 9600  | 4FSK | IL2Pc | FM     | 12.5k  | High SNR links between dedicated data radios. Suitable for UK 2m band.                     |
-|2 | 0010 | 9600  | 9600  | GFSK | IL2Pc | FM     | 25k    | Current recommended mode for new 70cm (25kHz) links where both ends are compatible         |
+|2 | 0010 | ? | 9600  | 9600  | GFSK | IL2Pc | FM     | 25k    | Current recommended mode for new 70cm (25kHz) links where both ends are compatible         |
-|5 | 0101 | 3600  | 3600  | QPSK | IL2Pc | FM     | 12.5k  | For situations where only a speaker/mic connection is available but > 1200 baud is desired |
+|5 | 0101 | ? | 3600  | 3600  | QPSK | IL2Pc | FM     | 12.5k  | For situations where only a speaker/mic connection is available but > 1200 baud is desired |
-|11| 1011 | 1200  | 2400  | QPSK | IL2Pc | SSB/FM | 2.4kHz | HF - quadrature version of 1200 BPSK, twice the throughput for +3dB SNR.                   |
+|11| 1011 | QPSK v26a | 1200  | 2400  | QPSK | IL2Pc | SSB/FM | 2.4kHz | HF - quadrature version of 1200 BPSK, twice the throughput for +3dB SNR.                   |
-|10| 1010 | 1200  | 1200  | BPSK | IL2Pc | SSB/FM | 2.4kHz | HF - use for circuits where wider transmission is acceptable.                              |
+|10| 1010 | ? | 1200  | 1200  | BPSK | IL2Pc | SSB/FM | 2.4kHz | HF - use for circuits where wider transmission is acceptable.                              |
-|9 | 1001 | 300   | 600   | QPSK | IL2Pc | SSB    | 500Hz  | HF - quadrature version of 300 BPSK, twice the throughput for +3dB SNR                     |
+|9 | 1001 | ? | 300   | 600   | QPSK | IL2Pc | SSB    | 500Hz  | HF - quadrature version of 300 BPSK, twice the throughput for +3dB SNR                     |
-|8 | 1000 | 300   | 300   | BPSK | IL2Pc | SSB    | 500Hz  | HF - slowest but best performing mode. ~7dB better than classic 300 baud FSK AX.25         |
+|8 | 1000 | BPSK AX.25 300bd | 300   | 300   | BPSK | IL2Pc | SSB    | 500Hz  | HF - slowest but best performing mode. ~7dB better than classic 300 baud FSK AX.25         |
-|14| 1110 | 300   | 300   | AFSK | IL2Pc | SSB    | 500Hz  | CRC improvement of IL2P 300 baud AX.25. Recommended if you can't do BPSK / QPSK on HF.     |
+|14| 1110 | AFSK AX.25 300bd | 300   | 300   | AFSK | IL2Pc | SSB    | 500Hz  | CRC improvement of IL2P 300 baud AX.25. Recommended if you can't do BPSK / QPSK on HF.     |
-|- | 1111 | n/a   | n/a   | n/a  | n/a   | n/a    | n/a    | Allows the mode to be set by a SETHW KISS command (v41+).                                  |
+|- | 1111 | ? | n/a   | n/a   | n/a  | n/a   | n/a    | n/a    | Allows the mode to be set by a SETHW KISS command (v41+).                                  |
 IL2Pc is shorthand for IL2P plus CRC.
+**QtSM NOTE: For IL2P and CRC modes, these need to be enabled per modem in the Settings/Modems menu**
 Superseded (but still supported) modes:
@@ Line 57: / Line 60: @@
 Baud is symbols per second, bps is bits per second. Where baud=bps, that means each symbol carries 1 bit (i.e. a symbol can have two states, 0 or 1). Where baud is 2x bps, that means each symbol carries 2 bits (i.e. a symbol can have four states: 00, 01, 10, 11).
+** Decoding Operating Modes from BrdSwchMod **
+When the test button is pressed on the TNC, along with the frame it emits to the radio, it will emit a different frame to the KISS client that is connected.  The BrdSwchMod value in the test frame can be decoded to share information about the TNC:
+  * the first two digits the board version (a decimal number, e.g. 04)
+  * the next two are the physical MODE switch setting (encoded as binary, for example 06 is 0110)
+  * the last four are the operating mode
+For example, for a value of ''BrdSwchMod:040F0023'' as used on the HF interface of GB7WEM, we can see:
+  * Board Revision 04
+  * MODE switch setting 1111 (set by SETHW hardware command)
+  * Current Operating Mode 0x23 (MODE_300_AFSKPLL_IL2P_CRC)
+The Operating Mode values are **internal** and **may change with firmware version**, so you can use the following table to map the operating mode values **for Version .44 of the Firmware** (current at time of writing):
+^ Switch Mode ^ BrdSwchMod Value ^ Mode Name                 ^
+| 0 (0000)    | 0x00             | MODE_9600_GFSK_AX25       |
+| 1 (0001)    | 0x41             | MODE_19200_4FSK           |
+| 2 (0010)    | 0xB0             | MODE_9600_GFSK_IL2P_CRC   |
+| 3 (0011)    | 0x40             | MODE_9600_4FSK            |
+| 4 (0100)    | 0xA3             | MODE_4800_GFSK_IL2P_CRC   |
+| 5 (0101)    | 0xF1             | MODE_3600_QPSK_IL2P_CRC   |
+| 6 (0110)    | 0x02             | MODE_1200_AFSK_AX25       |
+| 7 (0111)    | 0x93             | MODE_1200_AFSK_IL2P_CRC   |
+| 8 (1000)    | 0x91             | MODE_300_BPSK_IL2P_CRC    |
+| 9 (1001)    | 0x92             | MODE_600_QPSK_IL2P_CRC    |
+| 10 (1010)   | 0xA0             | MODE_1200_BPSK_IL2P_CRC   |
+| 11 (1011)   | 0xA2             | MODE_2400_QPSK_IL2P_CRC   |
+| 12 (1100)   | 0x31             | MODE_300_AFSK_AX25        |
+| 13 (1101)   | 0x22             | MODE_300_AFSKPLL_IL2P     |
+| 14 (1110)   | 0x23             | MODE_300_AFSKPLL_IL2P_CRC |
+| 15 (1111)   | 0xF3             | MODE_SET_FROM_KISS        |
 ===== Signals settings =====
@@ Line 332: / Line 369: @@
 The KISS MODE setting is written to flash memory. To prevent an immediate flash memory write, add 16 to the mode number in the KISS SETHW command - for example, the value 14 would become 30.
+**BPQ**
 BPQ supports this via the ''KISS'' command. For this command to work, you must set the mode DIP switches to 1-1-1-1 (or //on-on-on-on//), and be in SYSOP mode. To enter SYSOP mode, type ''password'' at the prompt. The prompt will respond with ''OK''. At this point, enter the command below:
@@ Line 341: / Line 380: @@
 * Remembering to add 16 to the value if you don't want the setting written to memory.
-**Examples**
+**BPQ Examples**
 kiss n is the port number - port 3 in these examples
@@ Line 352: / Line 391: @@
 | QPSK600 IL2Pc              | ''kiss 3 6 25'' | ''kiss 3 6 9''  |
+**Linux Kernel**
+When configuring the linux kernel you can add the value required to the ''kissparms'' command in your startup script. For this command to work, you must set the mode DIP switches to 1-1-1-1 (or //on-on-on-on//).  You would then modify the command to include the ''-h'' parameter with whatever value you require:
+<code>
+kissparms -p <port> -h <value as determined above*> <any other needed parameters>
+</code>
+* Remembering to add 16 to the value if you don't want the setting written to memory.
+**Linux Kernel Examples**
+^ Set port n to mode         ^ temporary*       ^ persistent      ^
+| FSK300 IL2Pc (40m slot 1)  | ''kissparms -p HF -h 30'' | ''kissparms -p HF -h 14'' |
+| BPSK300 IL2Pc (40m slot 3) | ''kissparms -p HF -h 24'' | ''kissparms -p HF -h 8''  |
+| QPSK600 IL2Pc              | ''kissparms -p HF -h 25'' | ''kissparms -p HF -h 9''  |
+* Note - for a startup script you should always use the temporary value rather than writing to memory each time
 === GPIO ===
 With Raspberry Pi GPIO, put /usr/bin in the crontab path, and add the following to /etc/crontab:
@@ Line 441: / Line 497: @@
 Available from [[https://tarpn.net/t/nino-tnc/n9600a/n9600a4/n9600a4-assembly.html|tarpn.net]], mirror {{ :packet:2020-11-21-ninotnc-n9600a4r2-sch.pdf | here }}
+===== Flashing CRC =====
+If your CRC light is flashing, you are driving the modem's RXA pin with too much audio, which is clipping. This is normally harmless but if you want to reduce it:
+{{:radios:tait-volume.jpeg?400|}}