radios:gm300
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
radios:gm300 [2023/07/16 14:27] – ei9iub | radios:gm300 [2023/07/16 14:44] (current) – ei9iub | ||
---|---|---|---|
Line 8: | Line 8: | ||
The radios are usually programmed through the front RJ45 connector, using a so-called RIB (Radio Interface Box). | The radios are usually programmed through the front RJ45 connector, using a so-called RIB (Radio Interface Box). | ||
Most cables purchased online are known as RIB-less, and are essentially USB - TTL devices such as the FT232x with a diode inline between TX / RX. | Most cables purchased online are known as RIB-less, and are essentially USB - TTL devices such as the FT232x with a diode inline between TX / RX. | ||
+ | |||
+ | It also possible to program these radios directly using the Raspberry Pi GPIO Serial pins, as the levels output are acceptable to the radio. | ||
+ | Be sure to map the serial port correctly, | ||
+ | |||
See below for a Homebrew Motorola RIBless cable schematic: | See below for a Homebrew Motorola RIBless cable schematic: | ||
- | FT232 -> Motorola GM300/GM340 (RJ-45) | + | FT232 -> Motorola GM300/GM340 (RJ-45) |
- | || | + | |
- | || | + | FT232 RJ45 |
- | || | + | +---+ 1N4148 |
- | || | + | |TXD|----|< |
- | || | + | +---+ |
- | || | + | +---+ |
- | || | + | |RXD|---------+-------+ |
- | || | + | +---+ |
- | || | + | +---+ |
- | || | + | |GND|---------------------+ |
- | || | + | +---+ |
- | || | + | |
- | || █ | + | |
- | || █▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄█░░ | + | The rear 16 pin accessory connector: |
- | || | + | |
- | || | + | |
+ | RADIO TOP | ||
+ | | ||
+ | | 2 | 4 | 6 | 8 | 10| 12| 14| 16| | ||
+ | +---+---+---+---+---+---+---+---+ | ||
+ | | 1 | 3 | 5 | 7 | 9 | 11| 13| 15| | ||
+ | | ||
+ | RADIO BOTTOM | ||
+ | AS SEEN FROM BACK | ||
+ | |||
+ | 1 EXT SPKR 9 EMERGENCY ALARM | ||
+ | 2 MIC AUDIO IN 10 IGNITION CONTROL | ||
+ | --> 3 PTT 11 RX AUDIO OUT < | ||
+ | 4 EXTERNAL ALARM 12 PROG I/O 12 | ||
+ | --> 5 FLAT TX AUDIO 13 SW A+ SENSE | ||
+ | 6 PROG I/P 6 14 PROG I/O 14 | ||
+ | --> 7 GROUND | ||
+ | 8 COS (PROG) | ||
+ | | ||
+ | Audio interfacing the Raspberry Pi and GM3X series radios. | ||
+ | These radios can also have PTT driven directly by the Pi without a transistor, but __this is not advised__. | ||
+ | | ||
+ | |||
+ | | ||
+ | | ||
+ | | ||
+ | | NPN | ||
+ | | ||
+ | |-----/ | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | |||
+ | | ||
+ | | ||
+ | | ||
+ | |||
+ | | ||
+ | | ||
+ | | ||
+ | |||
+ | | ||
+ | | ||
+ | | ||
+ | |||
radios/gm300.1689517667.txt.gz · Last modified: 2023/07/16 14:27 by ei9iub