Differences

This shows you the differences between two versions of the page.

--- waoarc25:kit-build-guide [2025/08/08 12:44] – [Filter Installation] gi3jmc
+++ waoarc25:kit-build-guide [2025/08/30 00:08] (current) – [WAOARC 2025 WSPR Kit Build - Construction Guide] gi3jmc
@@ Line 7: / Line 7: @@
 ----
-==== Prerequsites ====
+<WRAP group>
+<WRAP half column>
+<WRAP centeralign>
+Scan QR code to open this guide on mobile.
+{{ :waoarc25:kit_guide_qr.png?200 |}}
+</WRAP>
+</WRAP>
+<WRAP half column>
+<WRAP centeralign>
+[[software-guide-wsprrypi|Click here]] if you were looking for WAOARC 2025 WSPR Kit Software Preparation Guide
+{{ :waoarc25:software-guide-wsprrypi.png?200 |}}
+</WRAP>
+</WRAP>
+</WRAP>
+==== Prerequisites ====
 In your kit, you should have received the items in the table below. Please check you have everything before you begin:
@@ Line 47: / Line 70: @@
 <WRAP left round box half>
 Install the capacitors.
+You may find later steps easier if you leave fitting capacitor C1 until after the connectors are installed.
 **NOTE: C1 is an electrolytic capacitor so the orientation is critical or the magic smoke may escape.**  Long leg is positive, and short Leg is negative.  Match the white band on the capacitor to the white area on the board
@@ Line 79: / Line 104: @@
 ==== Diodes ====
 <WRAP left round box half>
-Install the diodes in poistions D1 & D2.\\
+Install the diodes in positions D1 & D2.\\
 Note the orientation of the diodes.  The LED short leg must be closest to the edge of the board.  The signal diode has a black stripe on one end which may be hard to see.  It should be positioned closest to the edge of the board, matching the outline on the board.
@@ Line 107: / Line 132: @@
 Wind the ferrite core with 4 turns of wire as shown.  Each time the wire passes through the centre counts as one turn.
-//Note: Crop the leads longer than necessary, and scrape, sand, or heat the coating to remove it before fitting and soldering.  Heating can be done with a lighter, or a very hot soldering iron.//
+//**Note: Crop the leads longer than necessary, and scrape, sand, or heat the coating to remove it before fitting and soldering.  Heating can be done with a lighter, or a very hot soldering iron.**//
 ^Reference ^Component ^
@@ Line 119: / Line 144: @@
 ==== Connectors ====
 <WRAP left round box half>
-Connector J2 (the 40-pin) is positioned on the underside of the board.\\
+Connector J2 (the 40-pin) is positioned on the **__underside__** of the board.\\
+__**WARNING: If you solder the 40-pin connector on the wrong side YOU WILL HAVE A BAD DAY. Check the picture to the right (below if on mobile).**__\\
 Connectors J5 & J6 are fitted to the component side of the board.\\
 Connector J4 (the SMA socket) is positioned on the edge of the board, with the centre pin connection on the top, component side of the board. All 4 ground pins should be soldered to the board, not just the pair adjacent to the centre pin.
@@ Line 148: / Line 174: @@
 <WRAP left round box half>
-When connecting your filter, (build instructions at [[https://qrp-labs.com/images/lpfkit/assembly_A4.pdf]]) you should ensure that is inserted in the correct orientation.  The filter has 'IN' and 'OUT' text on the ends, and you need the 'OUT' nearest the SMA connector.
+When connecting your filter, (build instructions at [[https://qrp-labs.com/images/lpfkit/assembly_A4.pdf]]), you should ensure that is inserted in the correct orientation.  The filter has 'IN' and 'OUT' text on the ends, and you need the 'OUT' nearest the SMA connector.
+Also, holding the filter with 'IN' on the left and the toroids facing you, check for continuity between the top left and top right pins.  If there is no connection, you have likely soldered on top of the coating on the wire, and have not burned it off.  Remove the toroid from the board and and scrape or heat the ends of the wire to remove the coating.  Fine sandpaper is easiest and works well.
 </WRAP>