Differences

This shows you the differences between two versions of the page.

--- radios:ic-7100 [2025/12/25 12:17] – [Low transmit power on SSB] m0mzf
+++ radios:ic-7100 [2026/01/08 00:05] (current) – g5rkt
@@ Line 91: / Line 91: @@
 ===== Low transmit power on SSB =====
-Some of these radios appear to have a problem with their ALC circuit (and / or possibly the compressor) causing them to put out low-ish power on transmit. The radio I have also seems to have this issue (putting out only around 60% desired PEP on normal speech, with the MIC gain, compressor and EQ set up). Some observations from playing with this radio on the bench: \\
+This is a widely reported issue, with lots of folks complaining the transmitter puts out low-ish power on SSB. The radio I have also seems to do this. Some observations from playing with this radio on the bench: \\
 - The radio puts out a full power CW / FM carrier \\
 - Modulation on FM / AM is good'n'strong, so there's no issue with the microphone / MIC gain controls \\
@@ Line 100: / Line 100: @@
 So in a testing environment the radio does put out the power one would expect. However, on real speech, it wasn't nearly as consistent: \\
 - When hollering "aaaaaaudio" into the microphone, driving the ALC to the top of the "normal" range and engaging 5-10dB compression, the radio only puts out ~40W when set to 100% power. Doing this on my 857d (for example) gives ~80W. \\
-- There appear to be some hidden time constants built into the radio which push and pull the ALC during normal speech - one syllable in one moment might produce 70W PEP, then 30W PEP, then 50W PEP. Very difficult to pin down, but in the dynamic environment of "real speech" the power output is somewhat inconsistent.
+- Maxing out the MIC gain and compressor, for the sake of science, makes no difference.
+- There appear to be some time constants built into the radio which push and pull the ALC during normal speech - one syllable in one moment might produce 70W PEP, then 30W PEP, then 50W PEP. Very difficult to pin down, but in the dynamic environment of "real speech" the power output is somewhat inconsistent.
 There are a number of solutions which have been mooted, so I tried 'em: \\
@@ Line 115: / Line 116: @@
 . Use the setup menu to adjust power output for a given audio input signal \\
-A mods.dk article suggests that Icom have made an error in their setup, and claims to completely solve this issue. The Icom service manual calls for a 30mVrms 1500Hz tone to be injected into the microphone socket and the TX power alignment to be performed. The article on mods.dk noted that other Icom manuals from the era, using the same model of microphone, specify this tone to be 1mV 1500Hz. He then set up the TX using 1mV audio instead of 30mV and claims to have solved the issue completely. I tried this and it **doesn't work**. Observations: \\
+A mods.dk article suggests that Icom have made an error in their setup, and claims to completely solve this issue. The Icom service manual calls for a 30mVrms 1500Hz tone to be injected into the microphone socket and the TX power alignment to be performed. The article on mods.dk noted that other Icom manuals from the era, using the same model of microphone, specify this tone to be 1mV 1500Hz. They then set up the TX using 1mV audio instead of 30mV and claims to have solved the issue completely. I tried this and it **doesn't work**. Observations: \\
-- When setting up the TX gain path the radio breaks HF into 160m, 20m, 10m. 6m / 4m (and also 2m / 70cm) are set up separately. \\
+- When setting up the TX gain path the radio breaks HF into 160m, 20m, 10m. (6m / 4m and also 2m / 70cm are set up separately) \\
 - On HF, one injects the audio tone and adjusts the radio to put out 50W. This first stage of adjustment happens in the 20m band. With this tone still being injected the radio then automatically sets the gain for 160m and 10m with a few subsequent button presses. \\
 - When injecting a 30mV audio tone this automatic setting on 160m and 10m works just fine \\
 - When injecting anything below ~15mV the radio cannot complete the auto-adjustment on 10m \\
 Therefore I'm not sure how this person managed to successfully align the TX using a 1mV audio input - and 1mV is rather too low anyway for a condenser mic. Who knows... YMMV.
-All this being said, these sorts of power differences don't make too much difference to intelligibility on the air. Readability and signal reports are, if they can be believed, just fine. My take is just use the radio as intended, and don't worry about it. Perhaps don't use it to drive a linear amplifier.
+All this being said, these sorts of power differences don't make too much difference to intelligibility on the air. Readability and signal reports are, if they can be believed, just fine. My take is just use the radio as intended, and don't worry about it. Perhaps don't use it to drive a linear amplifier!!